|
It is currently Tue Nov 19, 2024 1:21 am
|
View unanswered posts | View active topics
 
|
Page 1 of 1
|
[ 10 posts ] |
|
| Author |
Message |
|
gadwa1
|
Post subject: Wake Tower  Posted: Thu May 05, 2016 5:07 am |
|
Joined: Sat Apr 11, 2015 8:31 pm
Posts: 2
|
|
Hi guys I have an older A20 and my new shed is a fraction low, has any one tried to have a slightly shorter sides to hold the tower made up, I only want to shorten it an inch or two ? Was going to see if a metal fab place could make two new wake tower sides a fraction smaller? thoughts
Cheers Mike
|
|
| Top |
|
 |
|
paula.shane
|
Post subject: Re: Wake Tower Posted: Thu May 05, 2016 5:48 am |
|
 |
| Team Axis |
 |
Joined: Wed May 02, 2012 4:25 am
Posts: 84
Location: Adelaide Australia
|
|
Could you not just trim off what you need off to lower it and re drill the through holes?
2012 Axis A20
_________________
2012 Axis A20 Down Under
|
|
| Top |
|
|
|
r33pwrd
|
Post subject: Re: Wake Tower Posted: Thu May 05, 2016 6:43 am |
|
|
| Team Axis |
Joined: Sat Jun 06, 2015 10:35 pm
Posts: 1181
Location: Sammamish WA
|
|
Personally I think it would be easier to raise the sheds door opening an inch or two.
Sent from my SAMSUNG-SM-G925A using Tapatalk
_________________
-2015 A24 - 409 HP - 2249 Prop - 1100 rear sacs - 950 front sac - 290lb rider with Red Rocket and Phase 5 Quest
|
|
| Top |
|
|
|
onwi
|
Post subject: Re: Wake Tower Posted: Thu May 05, 2016 7:54 am |
|
|
| Team Axis |
 |
Joined: Thu Apr 11, 2013 6:19 pm
Posts: 199
Location: SE Wisconsin
|
|
Is your trailer as low as possible?
_________________
________
2012 A20
|
|
| Top |
|
|
|
vanamp
|
Post subject: Re: Wake Tower Posted: Thu May 05, 2016 8:32 am |
|
|
| Team Axis |
Joined: Wed Feb 05, 2014 9:02 am
Posts: 272
|
|
How much to tall is it exactly? If it really is fractions then let a little air out of the tires and experiment with different hitch heights.
Sent from my iPhone using Tapatalk
|
|
| Top |
|
|
|
admin
|
Post subject: Re: Wake Tower Posted: Thu May 05, 2016 1:57 pm |
|
|
| Site Admin |
 |
Joined: Wed Apr 21, 2010 9:00 am
Posts: 1115
|
|
I have heard of the tire trick. Let the air out and squeeze it under.
I have also heard of guys digging out the gravel for clearance. If your shed is on a gravel floor you might be able to dig down enough to clear.
|
|
| Top |
|
|
|
dustinjean
|
Post subject: Re: Wake Tower Posted: Thu May 05, 2016 7:17 pm |
|
|
| Team Axis |
 |
Joined: Wed Sep 03, 2014 5:19 am
Posts: 457
Location: Mt. Washington, KY
|
|
I personally wouldn't go modifying the tower itself. I had to remove the good looking fonished front on my boat shed I buily when I upgraded boats to gain a few inches but you can also adjust the axle height on the trailer
Sent from my SM-G900V using Tapatalk
_________________
2014 A24
|
|
| Top |
|
|
|
gadwa1
|
Post subject: Re: Wake Tower Posted: Sat May 07, 2016 4:07 am |
|
Joined: Sat Apr 11, 2015 8:31 pm
Posts: 2
|
|
Thanks guys but it may be as much as few inches, local regs say the shed can only be 3mtrs then there is the roller door putting it at 2.8, thought about leaving a grove on the cement for the tyres but its just not enough, with the shed and floor and driveway we are at almost 20k, Thanks any way
Mike
|
|
| Top |
|
|
|
r33pwrd
|
Post subject: Re: Wake Tower Posted: Sat May 07, 2016 5:14 pm |
|
|
| Team Axis |
Joined: Sat Jun 06, 2015 10:35 pm
Posts: 1181
Location: Sammamish WA
|
|
Just lower the trailer like said above..
Sent from my SAMSUNG-SM-G925A using Tapatalk
_________________
-2015 A24 - 409 HP - 2249 Prop - 1100 rear sacs - 950 front sac - 290lb rider with Red Rocket and Phase 5 Quest
|
|
| Top |
|
|
|
AJWest
|
Post subject: Re: Wake Tower Posted: Sat May 07, 2016 9:34 pm |
|
|
| Team Axis |
Joined: Mon May 23, 2011 11:02 am
Posts: 1849
Location: Copperas Cove, TX
|
|
Modify the trailer by maybe adjusting the torsion arm on the splines of the axle to bring it down a bit. Lower profile tires maybe?
_________________
2014 A24
2011 A22 (sad to see her go)
|
|
| Top |
|
|
|
|
Page 1 of 1
|
[ 10 posts ] |
|
Who is online |
Users browsing this forum: Google [Bot] and 47 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
